5 Simple Steps to Replace the Screen on Your Apple Watch Like a Pro
If your Apple Watch screen is cracked or broken, or if the touchscreen doesn’t respond when you touch it, you can go for apple watch screen replacement. The process is a little tricky and will require you to send your watch in for repair unless you’re handy with delicate electronics. If your Apple Watch isn’t eligible for service under warranty or consumer law, you can replace the screen using these instructions.
To replace your Apple Watch screen, you’ll need a replacement screen and tools to remove the old one. You’ll also need a micro-suction cup, adhesive remover, alcohol pads (such as PVA), plastic opening tools, and tweezers.
You can purchase replacement screens from Apple or third-party companies, but you’ll need to remove the old ones first. Here’s a step-by-step guide to removing and replacing your Apple Watch screen.
You’ll need the following tools and supplies:
A tri-pointed tool (the best option is a plastic opening tool)
A suction cup that will stick to glass (either a micro-suction or a suction cup with rubber tips)
A replacement screen (we recommend buying from reputable sellers on eBay and Amazon)
Apple Watch screen removal kit (sold separately)
The first step is to remove the band. You can find a guide on how to do this here. Once the band has been removed, you’ll need to remove the watch’s back cover by using your tri-pointed tool and prying it off gently.
You should be able to see the battery at this point. Use your suction cup to remove the battery by sticking it to the back of your watch. Next, use your suction cup to remove the screen. The screen should come out quickly. If it doesn’t, ensure you have removed all the adhesives from around it before trying again. If you are looking for iphone screen repair, then you canreach out to us.
The next step is to remove the circuit board. You can do this by prying up on the edges of each side until it comes out. It should come out quickly if you have removed all of the adhesives from around it.
Once the screen is removed, you’ll need to remove the micro-suction cup from your back cover. If you’ve never used one before, it can be a little tricky at first, but once you get the hang of it, they’re pretty easy! Apple watch screen replacement isnot an easy process and requires utmost precision.
First, you should suction the cup to your back cover. You’ll want to ensure that it’s pressed firmly against the surface, so it doesn’t fall off while trying to remove it. Next, use your razor scraper to gently scrape away at the micro-suction cup until it detaches from the back cover.
You’ll know it’s removed when you see little white dots on the back cover. If some are still left, repeat this process until they’re all gone. Once the micro-suction cup is removed from your device, clean off any remaining adhesive with isopropyl alcohol and a lint-free cloth or paper towel.
Alcohol pads (like PVA)
Once you’ve removed the micro-suction cup, wash your phone’s back cover with water and soap to remove any debris or dust. Then, using an alcohol pad (like PVA), gently clean the adhesive off your screen. Ensure you don’t leave any residue behind, as it will prevent us from adequately sticking down our new screen protector!
Once you’ve cleaned the surface of your phone’s screen, place the micro-suction cup back on top. Make sure it’s pressed firmly against the surface, so it doesn’t fall off while trying to remove it. Next, use your razor scraper to gently scrape away at the micro-suction cup until it detaches from your phone’s back cover.
Once you’ve removed the micro-suction cup, use a lint-free cloth to remove any remaining moisture from your screen. Then, place your new screen protector onto your phone’s back cover and press firmly against it.
Plastic opening tools
These tools are handy for opening up the back cover of your phone. They come in two different styles flat and pointed. The balanced variety is used to pry open the back cover of your phone, while the pointed one is used to remove any debris that may be stuck inside it.
The flat plastic opening tool is the easiest to use. You can use it just like a screwdriver, except you’ll be prying up instead of pushing down. It would help if you also had some cotton swabs handy in case any residual oils or dirt need to be cleaned off of your phone’s back cover.
If any small screws need to be removed, you’ll want a set of precision screwdrivers. These will help you get into those hard-to-reach places where your fingers just won’t fit.
Tweezers are handy in removing any debris that may be stuck inside your phone’s back cover. You can also use them to pry open the back cover if you have difficulty using the opening tool.
It would help if you also had some cotton swabs handy in case any residual oils or dirt need to be cleaned off of your phone’s back cover. There are many different types of tweezers available, but I recommend using a pointed one instead of the flat one because they’ll make it easier for you to reach into small crevices.
If you don’t have tweezers, you can use a toothpick instead. Make sure it’s clean since you don’t want dirt on your phone. It would help if you also had some cotton swabs handy in case residual oils or dirt need to be cleaned off your phone’s back cover.
There are many different types of tweezers available, but I recommend using a pointed one instead of the flat one because they’ll make it easier for you to reach into small crevices.
Unfortunately, the Apple watch screen replacement processis a more serious endeavor than most people will be able to handle unless they’re a bit handy and don’t mind minor damage to their devices. If you get your watch fixed at an Apple store or some other center, it will likely cost several hundred dollars (and more). And even after that payment, you won’t get an entirely new and undamaged watch.
If you are looking for a screwdriver factory to customize your screwdriver set, please do not hesitate to contact us, thank you!